+45 31 33 18 19
salg@GOmeasure.dk

Tektronix TSG4102A 2 GHz Analog signal generator

Tektronix TSG4102A 2 GHz Analog signal generator

Price on request

  • Analog and vector/digital signal generation capabilities
  • Dual baseband ARB generators
  • Analog modulation standard
  • Soft key upgrade to vector/digital modulation at very low cost
  • Digital modulation applications for GSM, EDGE, W-CDMA, APCO-25, DECT, NADC, PDC, and TETRA
  • USB, GPIB, RS-232, and LAN interfaces
  • 12 pounds (5.6 kg)
  • 2U high and half standard rack width

Tektronix TSG4102A 2 GHz Analog signal generator

The TSG4102A RF Vector Signal Generator offers mid-range performance and up to 200 MHz modulation bandwidth at an entry-level RF signal generator price. They use a new technique to provide spurious free outputs with low phase noise (-113 dBc/Hz at 20 kHz offset from 1 GHz carrier) and extraordinary frequency resolution (1 μHz at any frequency). The TSG4100A Series comes standard with analog modulation. Convenient, in-field software upgrades allow for easy transition from analog to more advanced vector and digital modulation capabilities, providing the most flexible configuration and best CAPEX protection. These instruments complement other leading mid-range RF test solutions from Tektronix, such as the USB-based RSA306 Spectrum Analyzer and MDO4000B and MDO3000 Mixed Domain Oscilloscopes.

The TSG4100A Series instruments use an ovenized SC-cut oscillator (TSG410xA-M00 or E1 models) time-base, providing a 100 X improvement in stability (and a 100 X reduction in the in-close phase noise) compared to instruments that use a TCXO time-base.

Key features

  • Analog and vector/digital signal generation capabilities
  • Dual baseband ARB generators
  • Analog modulation standard
  • Soft key upgrade to vector/digital modulation at very low cost
  • Digital modulation applications for GSM, EDGE, W-CDMA, APCO-25, DECT, NADC, PDC, and TETRA
  • USB, GPIB, RS-232, and LAN interfaces
  • 12 pounds (5.6 kg)
  • 2U high and half standard rack width

 

Key performance specifications

  • True DC to 2 GHz, 4 GHz or 6 GHz to support both analog and vector/digital signal generation
  • Typical ≤±0.30 dB amplitude accuracy (0 dBm CW signal at 22 ºC) from 10 MHz to 6 GHz
  • I/Q modulation inputs (400 MHz RF bandwidth)
  • ASK, FSK, MSK, PSK, QAM, VSB, and custom I/Q

Analog modulation

The Tektronix TSG4100A Series RF Vector Signal Generators offer a wide variety of modulation capabilities. Modes include amplitude modulation (AM), frequency modulation (FM), phase modulation (ΦM), and pulse modulation. There is an internal modulation source as well as an external modulation input. The internal modulation source produces sine, ramp, saw, square, and noise waveforms. An external modulation signal may be applied to the rear panel modulation input. The internal modulation generator is available as an output on the rear panel.

Vector modulation

The TSG4100A Series builds on this performance by adding full support for vector signal modulation on RF carriers between 400 MHz and 6.0 GHz. It features a dual arbitrary waveform generator operating at 125 MHz for baseband signal generation. The generator has built-in support for the most common vector modulation schemes: ASK, QPSK, DQPSK, π/4 DQPSK, 8PSK, FSK, CPM, QAM (4 to 256), 8VSB, and 16VSB. It also includes built-in support for all the standard pulse shaping filters used in digital communications: raised cosine, root-raised cosine, Gaussian, rectangular, triangular, and more. Lastly, it provides direct support for the controlled injection of additive white Gaussian noise (AWGN) into the signal path.

Internal baseband generators

Using a novel architecture for I/Q modulation, the TSG4100A Series provides quick, user-friendly waveform generation. The baseband generator supports the playback of pure digital data. It automatically maps digital symbols into a selected I/Q constellation at symbol rates of up to 6 MHz and passes the result through the selected pulse shaping filter to generate a final waveform updated in real time at 125 MHz. This baseband signal is then modulated onto an RF carrier using standard IQ modulation techniques.

Digital communications protocols (GSM, GSM EDGE, W-CDMA, APCO-25, DECT, NADC, PDC, and TETRA) quickly configure the signal generator to the correct modulation type, symbol data rates, TDMA duty cycles, and digital waveform filters. The preset protocols also configure the rear-panel TDMA, START of FRAME, and SYMBOL CLOCK digital outputs. The baseband generators can be configured for these protocols without the use of external computers or third party software.

The I/Q waveforms are computed in real time. Symbols are mapped to constellations, digitally filtered, and up-sampled to 125 Msps to drive the I/Q modulator via dual 14-bit DACs. The symbols can be a fixed pattern, PRBS data from an internal source, or come from a downloaded user list of up to 16 Mbits.

The constellation mapping can be modified by the user. Digital filters include raised cosine, root raised cosine, Gaussian, rectangular, linear, sinc, and user-defined FIR.

External IQ modulation

The rear-panel BNC I/Q modulation inputs and outputs enable arbitrary vector modulation via an external source. The external signal path supports maximally 400 MHz of RF bandwidth with a full scale range of ±0.5 V and a 50 Ω input impedance.

Power vs. frequency

All TSG4100A Series models have cascaded stages of amplifiers and digital attenuators to drive the RF output. Five stages can provide up to +25 dB of gain to -130 dB of attenuation in 156 digitally controlled steps. During factory calibration, the output power is measured at 32 frequencies per octave for each of the 156 attenuator steps to populate a memory matrix with about 40,000 elements. When set to a particular frequency and power, the instrument interpolates between these matrix elements to determine the best attenuator setting. An analog attenuator is used to provide 0.01 dB resolution between matrix elements and to compensate for residual thermal effects.

OCXO time-base

These instruments offer an oven-controlled crystal oscillator (OCXO) time-base. The time-base uses a third-overtone stress-compensated 10 MHz resonator in a thermostatically controlled oven. The time-base provides very low phase noise and very low aging.

Easy remote communications

Remote operation is supported with RS-232, LAN, and GPIB interfaces. All instrument functions can be controlled and read over any of the interfaces. Up to nine instrument configurations can be saved in non-volatile memory.

For more information: Tektronix

Tektronix TSG4102A 2 GHz Analog signal generator

Tektronix TSG4100A Series Datasheet

Tektronix TSG4102A 2 GHz Analog signal generator

Use the following information to choose accessories and options for your probes.

Models

For each of the basic models, there are three required but exclusive model options that need to be specified at the time of order: M00, M01, and E1. Pricing varies based on chosen option. See the Instrument Options section for details.

TSG4102A
Analog signal generator with 2 GHz frequency coverage, basic model
TSG4104A
Analog signal generator with 4 GHz frequency coverage, basic model
TSG4106A
Analog signal generator with 6 GHz frequency coverage, basic model
Accessory Description
RF cable 1 meter, N-type to N-type RF cable
Documentation CD All instrument models ship with a CD containing PDF files of user manuals in all available languages.
Installation and Safety Instructions All instrument models ship with a printed Installation and Safety Instructions manual (multi-language: English and Russian).
Calibration Statement of Calibration
Power cord Country specific (see Power cord options)

Warranty

Three years

Instrument options

Hardware options (All regions except North America)

Options M00 or M01 must be specified at the time of instrument order.

M00
Instrument with oven-controlled crystal oscillator (OCXO)
M01
Instrument with voltage-controlled crystal oscillator (VCXO)
GPIB
Adds GPIB interface

Hardware options (North America only)

Option E1 must be specified at the time of instrument order.

E1
Instrument with oven-controlled crystal oscillator (OCXO) time-base and GPIB interface

Hardware options (All regions)

TSG4100A-RM1
Single rack mount kit (can be ordered separately)
TSG4100A-RM2
Dual rack mount kit (can be ordered separately)
TSG4100A-ATT
30 dB, 5 W RF attenuator up to 6 GHz
D1
A list of performance verification test results

Software options

To upgrade to vector/digital modulation capability and/or add more modulation options after initial purchase, order “TSG4100A-UP + VM xx” instead of “TSG410xA VMxx”.

VM00
Basic vector modulation package with internal 6 MHz modulation bandwidth
VM01
GSM modulation (requires Option VM00)
VM02
GSM EDGE modulation (requires Option VM00)
VM03
W-CDMA modulation (requires Option VM00)
VM04
APCO-25 modulation (requires Option VM00)
VM05
DECT modulation (requires Option VM00)
VM06
NADC modulation (requires Option VM00)
VM07
PDC modulation (requires Option VM00)
VM08
TETRA modulation (requires Option VM00)
VM10
Audio Clip (analog AM and FM)
EIQ
External 200 MHz modulation bandwidth (requires Option VM00)

Power plug options

Opt. A0
North America power plug (115 V, 60 Hz)
Opt. A1
Universal Euro power plug (220 V, 50 Hz)
Opt. A2
United Kingdom power plug (240 V, 50 Hz)
Opt. A3
Australia power plug (240 V, 50 Hz)
Opt. A5
Switzerland power plug (220 V, 50 Hz)
Opt. A6
Japan power plug (100 V, 50/60 Hz)
Opt. A10
China power plug (50 Hz)
Opt. A11
India power plug (50 Hz)
Opt. A12
Brazil power plug (60 Hz)
Opt. A99
No power cord

Language options

Request the option below if you would like to order a printed verison of the English User Manual. (An electronic version of this manual is provided as a PDF on the CD that shipped with your instrument and is also available for download from the Tektronix Web site.)

Opt. L0
English manual

Service options

Opt. C3
Calibration Service 3 Years
Opt. C5
Calibration Service 5 Years
Opt. D1
Calibration Data Report
Opt. D3
Calibration Data Report 3 Years (with Opt. C3)
Opt. D5
Calibration Data Report 5 Years (with Opt. C5)
Opt. R5
Repair Service 5 Years (including warranty)

Additional information

Producent

Tektronix

Produktkategori

Analog Signal Generators

This website uses cookies. By continuing to use this site, you accept our use of cookies.  Learn more